Learn how to use Tobii Pro Glasses 2

Tobie glasses to the next generation wearable eye tracking tool from toby designed to enable easy precise and efficient collection of eye tracking data in a wide variety of real-world research scenarios today I'm going to show you what comes with your glasses to

package go through both how to set it up and make a recording as well as an overview of the basic features of the

glasses to product itself ok so let's look at what comes inside your box you'll get one of these boxes with some other things inside remove that all the

packaging take everything out of the box put the box to the side inside you'll have a carry case and a box full of accessories first we're going to have a

look at the carry case let's open it up as you can see there's a lot of stuff in here so we'll zoom in so we can show it all

to you a little bit easier ok so we have the head unit itself which comes with a clear plastic protective lens already attached we also have a tinted lens in the case as well this is the actual eye

tracker with several sensors that track what the person wearing it is looking at always handle the head unit with care and keep it clean as it is a delicate measurement instrument we also have the

recording unit and underneath that is a HDMI cable on the opposite side of the case we have four rechargeable type 1 8 6 5 0 batteries for different sized nose pads 3 SD memory cards a plastic

calibration card and a small section with a USB stick head strap cleaning cloth and a cable cord clip in on the underside of the lid is a small section which contains a QuickStart guide inside

the guide you'll find everything you need to get started with the glasses 2 let's open your accessories box again we're going to zoom in so this is easier

for you to see in here we have an Ethernet cable and Ethernet 2 USB adapter a couple of spare plastic calibration cards 10 calibration stickers a battery charger for your type

one eight six five zero batteries located in the carry case this charger comes with several different power adapters for different countries the UK the US Australia and New Zealand and the EU it also comes with a car cigarette

lighter plug power adapter so you can charge on the go there's also a USB power adapter that can power your recording unit as well as charging the battery that's inside it this also comes with several interchangeable plugs for

the same countries as mentioned earlier if you have the Premium Package you'll have another box with a Windows Pro tablet in this is designed to be used along with the Tobi glasses controller software you can of course

use any windows power tablet laptop or computer to control the glasses too as long as you have the controller software installed please check the user manual to make

sure your system meets the minimum system requirements before data collection please make sure to charge

all the batteries with the supplied battery charger the batteries are fully charged when the display above each battery reads 4.2 volts and three solid bars are shown like this also make sure

to prepare any SD memory cards you will need now to prepare your recording unit we need to insert a fully charged battery into the recording units battery compartment to do this we need to rotate

the battery cover counterclockwise to remove it and then insert the battery

positive end first and finally replace the battery cover and rotate it clockwise to secure it next we need to

install an SD memory card into the recording units memory card slot to do this we need to remove the rubber protector we need to make sure the SD card pins are facing towards the front of the recording unit as shown here then

insert the memory card okay so now that we have an SD card and a charge battery in the recording unit we can begin setting up for a recording to do this we're going to need the glasses to head-unit the provided HDMI

cable the prepared recording unit a nose pad the cable clip the head strap a calibration target a Windows tablet or computer with Tobi glasses control software installed and of course your

participant Simona here has very kindly offered to be my participant for today to make it easier to go through the steps okay we need to set up the head unit first to do this we must pick and attach a nose pad that will enable the

glasses to to sit naturally on your participant there are different sizes in

your carry case if the nose pad you choose does not sit correctly or feels uncomfortable for the participant simply

change it with a different size we need to get the HDMI cable and insert the micro HDMI end into the head unit then

secure the cable in the clip on the arm of your head unit we recommend using the head strap simply tighten it to ensure the glasses - do not move around or drop

during the recording next connect the other end of the HDMI cable from the glasses - into the recording unit and attach the recording unit to the

participant usually on a pocket or belt we provide a cable cord clip which can be clip to clothes in order to stop the wire catching or moving about too much

okay so now we have a participant set up with the glasses - hardware we want to get ready to make a recording please make sure that you have installed the glasses controller software on whichever Windows powered device you're going to

be using to control your glasses - there are two ways of connecting your glasses - to the Toba glasses controller software if you have the live view package you can only connect them via an Ethernet cable to do this please connect

the ethernet cable to your glasses - recording unit and then the other end of the cable to the device you are using to control your glasses - if you have either the live view wireless package or the premium package you can connect the

glasses through the Ethernet cable or you can connect them wirelessly over Wi-Fi to connect via Wi-Fi you first need to turn on your recording unit to do this you must press and hold the power button for a few seconds or until

the led stop flashing the network name of your glasses - will be the same as your serial number the serial number is located on a sticker on the rear of your recording unit near the bottom as shown

here make sure your windows power device has Wi-Fi enabled and then locate your glasses - in the list of available networks please allow up to two minutes from when you first powered on your recording unit for the device to appear

in your network list now connect to your glasses - the password is Tobi glasses with no spaces a capital T and the capital G once you have connected to your glasses - please open the Tobi

glasses controller software you will be at the dashboard where any connected glasses will be displayed locate the glasses you wish to record with make sure that the memory and battery life are not low these can be seen here if

you have more than one unit you may wish to rename your unit you can do this by clicking here on the Settings button and then clicking rename glasses choose

whatever name you wish and click Save Changes now we can click on start a new recording we must now either create a

new participant or choose one we've used before you can add any relevant info you wish to about the participant here when

finished please click create you should now be able to see the live view tab here you can see what the scene camera on the glass is to sees you need a calibration card or sticker if your

participant to view please ensure that the participant is placed between away from the calibration card instruct the participant to look at the center point of the calibration card and then

make sure you'll get engaged data indicated by the red circle if you are not getting gauge data adjust the head unit on the participants head or change the nose pad if you are getting gauge data instruct the participant to

continue looking at the center point until you tell them otherwise if both of these are true click the calibrate button if you're not happy with your calibration you can simply click on the

recalibrate button as shown here to try again make sure the participant is looking at the calibration target before you start the calibration process once the calibration is successfully completed and you can see that accurate

data is being received you are ready to start recording to start recording simply click on the record button and make the recording when you are finished recording simply click on the stop button in the glasses controller

software once your recording is started it does not matter if the recording unit becomes disconnected from the tablet or computer you must however reconnect your glasses recording unit to your computer to stop or pause the recording in the

Tobi glasses controller software during the recording you will see a live video from the glasses - in the controller software if the glasses are connected to your computer either by cable or by Wi-Fi this feature enables you to view

what the participant is looking at throughout the study if you wish to playback any of your recordings that are on the SD card inside the recording unit simply click on the relevant recording

under the recordings tab to view it you can also delete recording from here if you wish you can also click on the

participants tab here to view a certain participants recordings and information to turn off for the recording unit after you've finished your recording press and

hold the power button until the LED stop flashing you can use your carry case as a portable table wrist so you have a surface to place your tablet or device

on during recordings to convert your carry case into a portable table rest simply make sure the shoulder strap is connected to the opposite corners on the carry case as shown here then place it

over your head like so please be careful not to tilt the carry case too much when using it as a portable table wrist as you may drop your device now that we have collected our data with Toby glasses too

we can analyze it in Toby glasses analysis software please install Toby glasses analysis software on the windows device you intend to use the software with and then open the software the

software has to be purchased separately or it is included in the premium and subscription packages of Toby glasses too you will need a valid license key to install the software which you can find

in the product purchase email firstly we need to create a new project choose a name and where you want the project to be saved and click on create remove the

SD memory card from your recording unit and insert it into your PC we now find ourselves at the project dashboard from here we need to click on import glasses

recordings locate your SD memory card and click on the dot TT GP file to import the data next select which recordings you wish to import into the

project by clicking the checkboxes next to the appropriate recordings once the recordings are imported I can show you the basic features of Toby glasses analysis software these include a

snapshot mapping tool a visualization tool an Aoi tool as well as metrics and data exports let's look at a replay of a recording to start with to replay a tobe

glasses to recording with the gaze data overlaid just double-click on the recording in the recordings list in the replay tab click on the play button to replay the video you can use the

timeline and the replay control buttons to navigate in the video in this view you can also log interesting events that occur in the video in this case for example when the person is interacting

with the touch screen recipe Bank choose a name for the event you want to log choose what keyboard shortcut you want to use to log the event and click OK as

you can see it is now in the list of custom events but not in the events list when the interesting event occurs in the recording press the shortcut key to log the event this creates an event in the

events list in this case we would create an event for every time a participant starts interacting with the touch screen recipe Bank next we'll look at the mapping tool open a recording that you have a snapshot for

and would like to map gage data to snapshots are still images of objects of interest and by mapping gage data onto a snapshot image you can later use these to create visualizations and Aoi's or

areas of interest to import a snapshot you can click on snapshots and then the import snapshot button here locate and

select the appropriate snapshot and import it now we need to enable snapshot mapping by clicking here now you can see

your recording and snapshots side by side you need to find the point in time when your participant is looking at the snapshot now to map your data to the

snapshot all you need to do is click on the snapshot image in the same place as the Gaye's data is shown in the video once you have mapped all the data onto a snapshot move on to the visualizations

tool to get the visualizations tool click on the menu button and then click on the visualizations tab on the right hand side I will choose the snapshot we mapped to earlier as you can see by

doing this the software's automatically selected the recording that I mapped to this snapshot on the right hand side we have some options for what type of heat map the radius of the gaze plots the colors used the opacity and the

background you will also see any snapshots that you have used in your project as well as all your recordings listed in the data selection box edit these until you achieve what you're after then right-click on the image to

save your image to a file with your visualization data embedded within after you are finished head back to the project dashboard now we can go into the

Aoi or area of interest tool in this study we are trying to ascertain how much attention the interactive recipe Bank is getting so earlier we mapped the gaze data onto the snapshot every time the participant interactive with the

recipe Bank and now we can set up an area of interest for it there are several drawing tools here so you can create the correct shape for your area of interest the Aoi data will be used in the data

and all metrics export we will look at these next so click back to the project dashboard when you are ready so the appropriate data for your project

the metrics tab looks the same but with a list of different Aoi based metrics to choose from as you can see at the bottom

here is the data field of Aoi hid so if we just export the event time stamp and Aoi here we can see when the participant

looked at the recipe Bank of course you can choose as many of the data fields or metrics as you wish so we've gone through what comes with your Tobi

glasses to package how to set up and make a recording as well as how to install and use the hardware and both the Tobi glasses controller and analysis software's please consult the QuickStart

guide located in your carry case all the user manuals on the USB memory stick for more information for more helpful videos support and information please visit our website thank you for watching this Tobi

video see you next time